How To Make A Wind Generator - Essential Tips To Building Your Own Windmill
Author: Bryan Hufford
The notion of windmill power tends to fetch a bit of excitement back into our lives, causing us to fleetingly think back to our youthful days in school. Wind generators are gaining in value when we consider today's depleted natural resources and our troubled economy. Many people, in an effort to combat this dilemma, have decided to build their own wind power generators in an effort to save some of their hard earned money.
- Always begin your project by constructing a sturdy base to act as the windmill support. Since you will be positioning the windmill in one location, you should consider the use of concrete footings for holding the supports firmly in place.
- Your windmill tower can be made from strong plywood, but must be sturdy.
- You will want the blades to move frequently and in a free manner without any sort of hindrance.
- Premade quality blades will more then likely provide you with the best possible power. In the event this is not feasible, then you can make your blades out of strong plywood as well. The blades should be proportional to the size of the tower itself.
- Pay attention to the construction of your gear box, as this can actually be the weakest link in your complete project. The gearbox should permit the windmill to freely turn yet capture the energy that it makes.
There you have it. I have merely scratched the surface of the tips and hints.
Article Source: http://www.articlesbase.com/diy-articles/how-to-make-a-wind-generator-essential-tips-to-building-your-own-windmill-858852.html
About the Author
You need professional, step-by-step instructions on building your own windmill. Visit Build a Windmill, where you will learn more about windmill building and how you can get started making one of your own!
how would I make a wind generator?
I would like plans to make a wind generator for my home to run a few lights during a storm.
A motor is an electrical device that turns electrical energy into mechanical energy. I really don’t think that is what you’re after. You want to turn mechanical into electrical, right? Okay, in old cars, before they had alternators, they had generators. Snag one of these at a junk yard. It will charge a 12 volt DC battery. I have never done this, I am just theorizing as I type. Anywho, campers use 12 volt DC lighting as a back up. Heck even the fridges run on 12v, propane, NG, or AC. In theory, fabricate blades to this generator, with a voltage regulator and there you go. Actually, here is what I do. I used camping lighting that burns clean fuel and flashlights, but if you simply had an inverter, you could actually run a few things via you car. Another suggestion, a more serious one. Look at the way they make campers so self sufficient. 2 lighting systems, where one runs on AC and the other DC of 12 volt batteries. Not a bad idea for your house? They have there own battery charger, which you could put in your house, that keeps these batteries full whenever you are plugged into AC. Add a 12 volt light system to your storm center, add a camping stove with a small portable tank, vent the area. This stove could cook and serve as a source of heat. Get the fridge that runs on anything, what else do you need? Oh yeah, plans for a wind generator. Dragonfly Wind Generator. That’s what you are in need of. Perfect for residential.
this is a very simple process to do.
first get about 10 ft of wire.(must be coated with a wax or resine. you can get at radio shack for a couple of $)
then wind this around the motor. sand off both ends of the wire and connect to battery. if you do not have a motor get
a couple of magnets (also can get at radio shack) and tape or glue to axle. put in the wind and you have a turbine.
What is the best material to make propellers out of when making a wind generator? ?
something light and yet can make it spin fast. suggestions??
A wind generator is called a fan.
A wind powered device to convert wind power to some other form of energy is called windmill.
In both cases, carbon fiber would work very well.
An intriguing idea. Usually in this sort of generator the magnets are stationary and the coil of wire is on the rotor. If you don’t have much experience in physics or electricity i suggest you buy an experimental kit, like
http://sciencekit.com/electric-motor-generator-set/p/IG0024163/
When you have built the generator you can figure out how to attach it to a wind turbine. Good luck.
How can I wind vcr tape gears to make a wind generator?
I figure those VCR gears are small and light….. possibility for wind power?
How to make a wind generator ? to light for ex. light pulp?
I have idea of having a rotor with magnets attached to it, and wire surronding the magnet but not touching it.. is that going to produce electricity in the wires ? and if so how can i connect it to something with a positive and negative terminals ? sorry i have no experince in this kind of stuff.
if the wire is spinning how can i connect to any device for electreicity ??
1. you must understand some principles of how a generator works I would start here. http://en.wikipedia.org/wiki/Electrical_generator
2. Second it sounds like you mean a “hand crank” generator. This has been answered already here. http://answers.yahoo.com/question/index?qid=20080422194237AA4ZXeF
how to make a wind generator?
I have an old welding machine(which is basically a generator) that can make up to 250 amps. Can and how do I make it into a wind turbine and how do I hook it up to an U.S. standard house hold curcuit beaker. What other equipement do I need to possibly cut down my energy cost(i.e. car batteries, or larger capacity batteries) and is it worth my cost to build a frame to mount it to my roof or build a tower for it, to reap the benefits of wind generated power from scrape material.